Vapex 7.4v 3300mAh 30c Li-Po Car Hardcase (Tamiya)
Share on Facebook Share on Twitter Share via E-Mail Share on Digg

Product 1 of 2
This product was added to our catalog on Monday 19 September, 2011.

Vapex 7.4v 3300mAh 30c Li-Po Car Hardcase (Tamiya)

Model vap-lipo33T
Manufacturer Vapex
Status: Back Order Only
Price:   £22.50

7.4v 3300mAh 30c Li-Po Car Hardcase Rechargeable Battery

with Tamiya connector

Top brand Pro Packs 

RD330- 2S2P-7.4V 3300mAh-30C

1. Dimension: 137mm*46mm*25mm Hardcase (Car 7.2v Pack Size)

2. Tamiya 14# Silicone Wires

3. Balance lead with JST-XH series connector

4. Weight: 202g

5. Discharge Current: 30C (99amps!)  Burst (198amps!)

Tested at 90.17amps for 2.08 min run time!

Tested at 60.16amps for 3.22 min run time!

Tested at 30.04amps for 9.45 min run time!

The ability of the battery to deal with very high current on demand will give your motor any amount of power it needs with at a higher voltage and lighter weight too. This pack will fit in any car that takes a 7.2v sub c pack. Comes with case and lead.

Faster than any nimh packs 7.2v and longer run times than 4300mAh nimh packs.

Understanding LiPos

LiPo batteries are very different from previous generation batteries and understanding how they work, and especially how to charge them, is the key to getting the best performance.


Individual Lithium Polymer cells have a nominal voltage of 3.7 volts (vs. 1.2volts per cell for Ni-Cds or NiMHs). Cells are wired in series to give the following pack voltages:
1 cell = 3.7 volts
2 cells in series = 7.4 volts
3 cells in series = 11.1 volts

Unlike Ni-Cd and Ni-MH batteries that self-discharge when wired in parallel, LiPo cells can be hooked up, charged and discharged in parallel with no detrimental effect. Wiring two LiPo cells in parallel doubles the capacity (more run time), plus an important advantage of wiring in parallel is that each cell only sees half the total current.

3S 2P
A battery pack that has three cells in series (giving 11.1 volts) and 2 of these 3-cell packs are wired in parallel is commonly referred to as a 3S, 2P (3 series, 2 parallel).

C Rating
LiPo cells are also commonly given a C or current rating. This is the maximum average recommended discharge current for the cell. For example, the VP2150/20C packs have a 20C rating. To determine the maximum recommended discharge rate multiply the capacity times the C rating. 2150mAh x 20C = 43,000. So the maximum recommended discharge rate would be 43,000mA or 43 amps. If your application has a higher amp draw, remember that LiPo cells can be wired in parallel, and with 2 cells in parallel each cell sees half the total current. With 3 cells in parallel, each cell see one third the current.
By wiring packs in a combination of series to get the voltage and parallel to achieve the capacity and individual cell current to an acceptable level, LiPo cells can be used to power nearly every type and size of model.

Charging LiPo batteries requires a very different charge method than other types of cells. It's imperative to use a charger designed specifically for LiPo batteries, and with most LiPo-specific chargers it's necessary to correctly select the cell count (1, 2 or 3 cells) manually.